購買的混凝土攪拌車上裝如何正確的安裝調試？_公司新聞_自動混凝土攪拌機知識_自動混凝土攪拌機_自動混凝土攪拌車廠家

站內搜索

自動混凝土攪拌機知識

公司新聞行業資訊

熱點

自上料混凝土攪拌機空氣濾清器如何正確保養？

2021-01-05

攪拌車罐實現邊走邊轉需要做什么？

2021-10-03

小型自動混凝土攪拌機為什么會(huì )出現噪音？

2021-05-12

攪拌車保養需要注意的四大要點

2020-05-12

關于山汽

聯系人：劉老師

電話：400-879-1999

公司：山東山汽工程機械（集團）有限公司

地址：山東省萊州市206國道與308省道交叉口東南50米

購買的混凝土攪拌車上裝如何正確的安裝調試？

所屬分類：公司新聞發布時間：2021-04-16 來源：http://www.bosplumbing.com/ 瀏覽量：0

如今因為很多原因造成的，在農村有很多閑置的農用車輛。也有很多客戶在了解后，知道了如今可以把這些閑置的車輛進行改裝成小型混凝土攪拌車在農村使用，既能有效的進行閑置車輛的利用又能帶來不錯的經濟效益。

Nowadays, due to many reasons, there are many idle agricultural vehicles in rural areas. There are also many customers who know that these idle vehicles can now be converted into small concrete mixer trucks for rural use, which can not only effectively use the idle vehicles, but also bring good economic benefits.

那么今天小編就給大家詳細的介紹下，我們在購買了混凝土攪拌車上裝后如何進行安裝調試：

Today, Xiao Bian will give you a detailed introduction about how to install and debug the concrete mixer truck after it is purchased

1、安裝前應車輛底盤上的污物,使攪拌車上裝能平穩放置在底盤上面。

1. Before installation, the dirt on the vehicle chassis shall be removed to make the upper part of the mixer be placed on the chassis smoothly.

2、將攪拌車上裝吊放于車輛底盤上,使攪拌車上裝底架與車輛底盤大梁對齊,用騎馬螺栓將攪拌車上裝緊固于底盤上?；炷翑嚢韫?/div>

2. Lift the mixer truck upper assembly onto the vehicle chassis, align the mixer truck upper assembly underframe with the vehicle chassis beam, and fasten the mixer truck upper assembly onto the chassis with riding bolts. Concrete mixing tank
全自動攪拌車

3、連接各液壓管路,若所選為自卸車底盤,則直接用取力器連接齒輪泵即可:若為普通車型,則須根據車型配置取力器,再與齒輪泵連接。

3. Connect the hydraulic pipelines. If the dump truck chassis is selected, the power take-off can be directly connected to the gear pump. If it is an ordinary vehicle, the power take-off must be configured according to the vehicle type, and then connected to the gear pump.

4、檢査各部件的潤滑情況及液壓油箱的儲油量(從油箱上液壓溫度計觀察,油面少應位于溫度計的3/4處,攪拌車上裝才能正常運轉)。

4. Check the lubrication condition of each part and the oil storage capacity of the hydraulic oil tank (from the hydraulic thermometer on the oil tank, the oil level should be at least 3 / 4 of the thermometer, and the mixer can operate normally only when it is installed on the tank).

5、發動車輛使攪拌車上裝空轉,觀察有無異響,各液壓管路有無泄露,若無異?，F象,即可裝料運行。

5. Start the vehicle to make the mixer idle, observe whether there is abnormal noise, whether there is leakage in each hydraulic pipeline, if there is no abnormal phenomenon, it can be loaded to run.

上一頁：自動攪拌車剎車異常怎么判斷？下一頁：自上料攪拌車有哪些零件需要經常更換？

熱門產品 / HOT PRODUCT